Last updated November 18, 2026








Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Windows & Doors Troubleshooting: Common Problems and How to Fix Them
A door that sticks in July and swings freely in December is not a hardware problem. It’s a framing or slab movement problem, and replacing the lockset will cost you around $200 and fix nothing. We see this exact misdiagnosis weekly in North Las Vegas: a homeowner buys new weatherstripping for a draft that’s actually coming through a failed window seal, or pays a handyman to plane a door that’s binding because the frame has racked. The symptom almost always sits one level downstream from the cause. This guide maps those symptoms to the real causes, gives you the price range for each repair, and tells you which tests you can run yourself before you call anyone.
Quick Answer
Most window and door problems trace back to four root causes: failed weatherstripping or seals that let air and water through, insulated glass units (IGUs) that lose their seal, structural movement (settlement, framing rack, seasonal wood expansion) that changes how a door or window fits its opening, and water intrusion at flashing, sill, or frame-to-wall joints. The fix depends entirely on which one you have, so the first job is diagnosis, not hardware. Below, each symptom gets a cause, a test, and a realistic North Las Vegas price range.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Table of Contents
- Symptom-to-Cause Diagnostic Table
- Drafty Windows: Three Different Causes, Three Different Fixes
- Condensation Between Panes: It’s a Seal Failure, Not Dirt
- Doors That Stick: Seasonal Wood vs. Settlement vs. Hinge Pull
- Water Intrusion: Flashing, Sill, or Frame-to-Wall Joint
- Door Frame Racking from North Las Vegas Soil Settlement
- The Hardware Failure Sequence: Trace It Before You Buy
- What Each Repair Should Cost in North Las Vegas
Symptom-to-Cause Diagnostic Table
Before you call a contractor, match your symptom to the row below. The “what it usually means” column is where the money is saved, because it tells you whether you’re looking at a $40 fix or a $900 fix.
| Symptom | Most Likely Cause | Confirming Test |
|---|---|---|
| Draft at the edges of a closed window | Compressed weatherstrip or gasket | Dollar-bill test along the perimeter |
| Draft across the whole sash or frame | Frame-to-wall seal (caulk/foam) failed | Incense or thermal camera scan |
| Cold/hot glass surface, no edge draft | IGU gas lost, glass only | Thermal camera shows temperature uniformity |
| Fogging or haze between panes | Insulated glass unit seal failure | Visible; tap test for loose desiccant |
| Door sticks, seasonal | Wood swelling from humidity | Track whether it eases in dry months |
| Door sticks year-round, one corner | Frame rack / settlement | Check door reveal gaps at top and hinge side |
| Door sags, rubs at latch side top | Hinge pull or loose screws | Tighten; if screws spin, wood is stripped |
| Water stain under window, drywall | Flashing or sill pan failure | Spray test from outside; watch inside |
| Water stain at door threshold corner | Frame-to-wall joint or threshold seal | Check exterior joint for gaps and old caulk |
| Window won’t lock | Operator mechanism, sash warp, or frame twist | Check sash alignment first, then operator |
If two rows apply to the same opening, you have two problems stacked on each other. Treat the structural one first. Fixing the weatherstrip on a window in a racked frame is throwing money at a symptom.
Drafty Windows: Three Different Causes, Three Different Fixes
Every draft complaint we get in North Las Vegas lands in one of three buckets, and they cost wildly different amounts to fix.
1. Weatherstrip or gasket failure
The soft seal around the sash has compressed, dried, or torn. This is the cheap one. A dollar-bill test confirms it: close the window on a bill at several points around the perimeter. If you can slide the bill out with almost no resistance at a spot, the weatherstrip there is gone. Replacement runs roughly $15 to $40 per window in materials, and a contractor will charge a service call in the $80 to $150 range to replace it correctly.
2. Frame-to-wall seal failure
If the draft is coming around the entire opening, not just at the sash, the problem is the joint between the window frame and the rough opening. That’s outside the window itself. Caulk or backer-rod foam around the frame has failed, often after thermal cycling. A spray can of expanding foam won’t fix this correctly if the gap is deep; a contractor will pull trim and repack with proper backer rod and sealant. Budget $150 to $400 per opening depending on trim removal.
3. IGU seal failure
The insulated glass unit itself (the sealed double or triple pane) has lost its gas fill or its edge seal. The glass feels cold or hot to the touch across the whole surface, and there’s no edge draft. This is the expensive one, and it’s the one most homeowners misdiagnose as “the window is old.” Replacing the glass unit runs $180 to $500 per unit; replacing the whole window frame runs $600 to $1,400 installed.
If you have an older North Las Vegas home where every opening is drafty, the honest answer is often that the windows were originally fitted without proper air sealing. In those cases the fix is a window package, not a repair – which is a scope conversation for a Rowan Construction Group North Las Vegas home project visit, not a repair call.
Condensation Between Panes: It’s a Seal Failure, Not Dirt
Fog, haze, or visible droplets between two panes of glass mean the IGU’s edge seal has failed and the desiccant inside has saturated. You cannot clean it. The moisture is inside a sealed unit that is no longer sealed.
The tap test: gently tap the center of the glass. If it sounds like a dull thud instead of a crisp ping, the unit has likely lost its gas fill. A thermal camera makes it obvious: a failed unit shows a blotchy temperature pattern across the glass, while a sound unit reads uniform.
Can you replace just the glass unit?
Sometimes. Three conditions have to be met:
- The frame itself is structurally sound – no rot, no cracking, no visible warp.
- The unit is a standard size the glass supplier can fabricate. Custom sizes cost more but are possible.
- The frame design allows the sash to be removed and re-glazed without destroying the frame.
If any of those fail, the full window has to go. In our experience across North Las Vegas, roughly six out of ten fogged windows we’re called to can be re-glazed; the other four need a full replacement. The cost difference is substantial: glass-unit-only runs $180 to $500 per window, while a full unit runs $600 to $1,400 installed.
Doors That Stick: Seasonal Wood vs. Settlement vs. Hinge Pull
Sticking has three distinct causes, and they don’t share a fix. Match yours using the timing and location of the bind.
Seasonal wood swelling
If the door sticks in July and swings free in December, the wood panel or the jamb is absorbing summer humidity. This is common in older solid-core doors and in exterior wood doors. The fix is to reduce the swelling: refinish the door with a proper exterior-grade sealer (a contractor will do this for $200 to $450 including sanding and two coats), and confirm the door has clearance on all four edges. Don’t reach for the planer yet.
Frame rack from settlement
If the door binds year-round at one corner – usually the top hinge side or the top latch side – the opening has moved. Check the reveal (the gap between the door and the jamb) at the top and along the hinge side. If the reveals are wedge-shaped (wider at one end of the top, or unequal top to bottom), the frame has racked. The fix is to reset or shim the frame, not to plane the door. Planing a door in a racked frame buys you a few months before it binds again.
Hinge pull
If the door sags and rubs at the top of the latch side, the top hinge screws have pulled from the jamb. Tighten them. If they spin without biting, the wood is stripped. The right fix is to enlarge the screw hole and drive a longer screw into the stud behind the jamb, or replace the jamb section. Cheap fix (tighten or longer screws) runs $50 to $100; hinge jamb repair runs $150 to $350.
Water Intrusion: Flashing, Sill, or Frame-to-Wall Joint
Water stains at a window or door are diagnostic gold. Where the stain appears tells you which of three layers failed.
- Stain at the top of the interior trim: head flashing (above the window or door). The flashing either wasn’t installed, was installed wrong (lapped the wrong direction), or its sealant has failed. Fix: $300 to $800 depending on trim removal and flashing replacement.
- Stain at the bottom corners, inside: sill pan failure. The sill pan is the sloped, water-shedding pan under the window that channels water out toward the exterior. If it wasn’t installed or wasn’t sealed, water pools and finds its way inside. Fix: $400 to $1,000 per opening.
- Stain at the sides or in one corner of the frame: frame-to-wall joint. The sealant at the exterior perimeter has cracked, or the joint was never properly sealed. This is the cheapest fix at $150 to $400, but only if you catch it early. Behind the stain, if the drywall is soft, expect rot repair on top of that.
For a window or door installed in the last 24 months (i.e., still under any installer’s workmanship warranty), any of these is a callback, not a new job. Call the installer. North Las Vegas homes built in the last five years with water intrusion at openings are often showing installer error, not material failure, and the fix belongs to whoever installed it.
Door Frame Racking from North Las Vegas Soil Settlement
This is the North Las Vegas-specific problem that shows up more than most homeowners expect. A meaningful share of the housing stock here was built on expansive soils and on fill that was placed, graded, and not always left to settle for a full cycle before framing. Over five to fifteen years, that movement shows up as doors that bind, drywall corner cracks, and windows that suddenly won’t slide.
How to tell settlement racking from a hardware problem:
- Look at the interior reveals on the door or window. A racked frame has unequal gaps at the top – narrower at one end, wider at the other. A hardware problem leaves the reveals even.
- Check the wall above the opening for a stair-step crack running diagonally from a corner. Settlement almost always leaves this signature.
- Check if other openings in the same wall show the same bind. One door binding could be hardware. Three doors in the same wall is the wall.
If you have reveals uneven by more than 1/8 inch, plus a diagonal crack above, the correct fix is to re-level and re-shim the frame, not to re-plane the door. Re-planing a door in a racked frame costs $150 to $300 and buys you perhaps two seasons. A proper frame reset runs $400 to $900 per opening, and if it turns out the footing or slab under the wall has moved further than shimming can correct, that’s an engineering question, not a carpentry one. We flag this because a door that won’t shut in a wall that has moved is worth understanding before you spend on cosmetics.
The Hardware Failure Sequence: Trace It Before You Buy
“The window won’t lock” is the point where most homeowners reach for a replacement lockset. Slow down. A window that won’t lock has three possible root causes, and the lockset is the third one. Trace them in this order:
- Operator mechanism (for casement and awning windows). The crank, the linkage arm, or the gearing has worn, and the sash isn’t closing far enough to seat the lock. Test: open the window, then slowly close it with the crank. If the sash doesn’t sit flush to the jamb, the issue is the operator. Replacement operator: $40 to $90 in parts, $150 to $300 installed.
- Sash warp. A wood or vinyl sash that has warped doesn’t close squarely. Test: hold a straightedge against the sash edge; a visible gap means warp. Repairing a warped sash is often not economical – the sash either needs full replacement or the window unit goes. Plan $400 to $900 for sash-only replacement, or the full window cost if the frame is also compromised.
- Frame twist. The frame itself has bowed so the locks don’t align. Test: check whether the reveals are equal along the sash. Frame twist often comes from settlement (see the prior section), and correcting it requires re-shimming the frame, not new hardware.
We carry the same checklist on every North Las Vegas window service call. Replacing a lock cylinder on a frame that has twisted is the classic waste of $200 – the new lock won’t latch either.
What Each Repair Should Cost in North Las Vegas
Here’s the price range we would expect a competent North Las Vegas contractor to quote for each common repair, materials and labor. Use it to check a diagnosis against realistic numbers before you authorize work. If someone quotes you $1,400 to replace weatherstrip, that’s a red flag. If someone quotes $85 to re-glaze a fogged IGU, that’s also a red flag – it can’t be done that cheaply with quality materials.
| Repair | Typical Range | Notes |
|---|---|---|
| Weatherstrip replacement (per window) | $80 – $150 | Includes service call and materials |
| Frame-to-wall air sealing (per opening) | $150 – $400 | Add for trim removal and replacement |
| IGU / glass-only replacement (per unit) | $180 – $500 | Assumes sound frame |
| Full window replacement (per unit, installed) | $600 – $1,400 | Varies with glass package and size |
| Exterior door refinish (sanding + 2 coats) | $200 – $450 | For seasonal swelling, not settlement |
| Hinge tightening / longer screws | $50 – $100 | If jamb wood is intact |
| Hinge jamb repair | $150 – $350 | When screws no longer bite |
| Frame reset / re-shim (racket frame) | $400 – $900 | Per opening, assumes shim-level fix |
| Head flashing replacement (per opening) | $300 – $800 | Includes trim work |
| Sill pan repair (per opening) | $400 – $1,000 | Sill pan must be re-formed, not just caulked |
For context, a full exterior door replacement – frame, slab, threshold, hardware, trim, painting – runs $1,200 to $2,800 in the North Las Vegas market depending on the door. If a repair quote is approaching that number for a problem that could be fixed by re-shimming, ask why. Our Fence Installation in North Las Vegas crews see the same settlement patterns at fence posts and gate frames that window and door clients see at openings, which is one reason we can usually identify the pattern on sight.
Common Mistakes to Avoid
- Replacing the lockset when the window won’t lock. Trace operator, then sash warp, then frame twist. Hardware is the third cause, not the first, and replacing it on a warped sash costs $200 and works for a month.
- Caulking a fogged window from the inside. The fog is between the panes; interior caulk has nothing to do with it. You’re sealing a spot that was never open in the first place, and the unit will keep fogging.
- Planing a door that binds in a racked frame. In North Las Vegas, this is the most expensive cheap fix. Planing trims the door to fit a moving opening: it binds again next season, and now the door is smaller. Diagnose the frame first.
- Weatherstripping over a frame-to-wall joint that has failed. New weatherstrip on a window whose wall joint is leaking doesn’t draft-proof anything. It hides the symptom until the next moisture event.
- Ignoring water intrusion for a season. A $250 flashing repair becomes a $2,400 rot repair when the drywall behind the stain is soft. Water at a window is a this-month problem, not a this-year problem.
- Buying a $900 window without re-checking the frame first. New window in the same bad opening racks the same way. The frame is a part of the system.
- Adding weatherstripping to a sliding door track that’s binding. If the door can’t slide freely, a heavier seal on the track makes it bind harder. Fix the track and rollers first, then address the seals.
See the difference
Before
After
Before
After
Before
AfterWhen to Call a Professional
Most of the tests in this guide are safe to run yourself: dollar-bill test, tap test, thermal camera scan if you have one, checking reveals and stains. Call a professional when:
- Water intrusion has any visible interior staining, because the diagnosis (flashing vs. sill vs. wall joint) depends on pulling trim carefully.
- A door or window has racked (uneven reveals), because re-shimming a frame requires resetting the casing, the trim, and often the drywall at the opening.
- You have a full window or door unit to replace, because the trim, flashing, and air-sealing work rarely survives a DIY attempt with any warranty intact.
- You have multiple openings in the same wall failing at once – that’s a wall-level issue, and it wants a site walk.
If your inspection turns up a broader condition – movement, moisture, siding, roof flashing feeding the same problem – the repair often turns into a scope conversation that touches multiple trades. Rowan Construction Group North Las Vegas offers free estimates in North Las Vegas and can walk the whole house with you in one visit. Call (844) 708-4417 to schedule. For readers who are already thinking about a larger project that includes replacing your front entry or slider while you’re at it, our Home Additions & ADU in North Las Vegas team can pull the window and door schedule into the same scope discussion so you’re not paying for the same trim removal twice.
Frequently Asked Questions

It’s almost always wood swelling from summer humidity – not a hardware problem. Interior relative humidity in North Las Vegas climbs in monsoon season (July through September), and a solid-core door absorbs that moisture and swells into its jamb. Refinishing the door with a proper exterior-grade sealer reduces the swing. If it sticks year-round instead, look at frame rack, not weather.
No. Condensation between panes means the insulated glass unit’s edge seal has failed and the desiccant inside has saturated. The moisture is inside the sealed cavity, not on the surface, so no cleaner can reach it. The unit must be re-glazed (glass-only, $180 to $500) or the whole window replaced ($600 to $1,400). Call (844) 708-4417 if you want a firm number for your windows in North Las Vegas.
Usually, yes, if the frame is sound, the sash can be removed for re-glazing, and the glass unit can be fabricated to your opening. Three out of five fogged windows we see can be re-glazed. The other two need a full unit, usually because the frame itself is showing rot, warp, or settlement movement.
Different lots settle differently, and North Las Vegas has wide variation in soil conditions across neighborhoods. A home on fill that wasn’t left to settle for a full cycle will show door binding earlier than a home on native soil. If you have one door binding, it may be the frame. If you have three or four doors binding in the same wall, the wall itself has moved.
A weatherstrip draft is felt at the sash edges – along the perimeter between sash and jamb. A frame-seal draft comes from the entire opening, often where the interior trim meets the drywall. The dollar-bill test isolates the first; a lit incense stick around the trim isolates the second. Both drafts can exist simultaneously on the same window.
Yes – any replacement that changes the size of the rough opening or the performance rating of the unit is a permitting event, and North Las Vegas enforces it. Like-for-like replacement of an existing unit in the same opening is usually permitted under a trade permit or may not require a permit; we confirm at the site walk. Written line-item quotes and documented photo records on every visit are standard on every Rowan job. Call (844) 708-4417 for a free estimate or a free second opinion on any written quote you already have.
The Bottom Line
Window and door problems are a diagnostic exercise first and a repair second. A draft is usually one of three different failures; fogging is a failed seal, not dirt; sticking is hardware only after seasonal wood and frame rack have been ruled out; and water intrusion is always a layer question (flashing, sill, or wall joint). The two tests that return the most on a five-minute investment are the dollar-bill test at the perimeter of every window and a reveal check at every sticking door – those two won’t tell you what to fix, but they will rule out what not to fix. Most misdiagnosed repairs in North Las Vegas are in that second category. Once you know the cause, the price table above should match a contractor’s quote closely. If it doesn’t, ask.
Rowan Construction Group North Las Vegas writes a price before any work starts, on every trade, every time. Need a second look at a window or door quote? Our team will review any written estimate line by line at no charge. For full-home projects that touch windows and doors alongside structure or exterior work, our Driveway & Pavers in North Las Vegas crews regularly see the same settlement signature at hardscape edges, which is why we walk the whole property with clients before scoping.
Contact

Call (844) 708-4417 for a free estimate in North Las Vegas. We’ll walk every opening, run the tests with you, and write the number before anyone picks up a tool. Same for a second opinion on a quote you have in hand – that’s free, too.
Written by the team at Rowan Construction Group North Las Vegas.


